(Extreme Duty XTP Front Sight/Muzzle brake with bayonet lug)
Available in stainless or black
Shown with Urban Brawler see through rail $139.99 maintaining the open sight picture.
Full Accessory Rail $159.99 & New Fully Adjustable Rear Sight $79.99 (No tools needed to adjust)
|
|
|
|
- New Base Rifle Ruger Mini 14 or Mini 30 Price - Blued $699.99 or Stainless Steel $739.99
- XTP Front Sight & Muzzle brake Installed Add $199.99. (Barrel can be cut and re crowned to 13.5" then Permanently attaching the XTP brake to make the barrel legal @ 16" Or your choice of cutting barrel to 16" or 18" then adding the XTP Front Sight & Muzzle brake)
- See Thru Scout Rail Add $89.99
- Forward right accessory short rail on stock. Add $39.99.
- Tactical Stock with cheek swell Add $99.99.
- M1 A Carbine style rear sight fully adjustable with your fingers. Add $79.99
- Trigger Job. Fantastic Nice crisp 3.5lbs pull with short take up!! Add $65.00
- (WHEN ALL IS COMBINED WHAT A SHOOTER! (Capable of MOA Accuracy)
Above: 16" Fluted Ultra Match Barrel w/ .875" Varmint size Gas Block
Above: 20" Fluted Ultra Match Varmint Barrel
Above: 20" Fluted Ultra Match Medium Barrel - 50/50 .875" Down to .750"
Above: Shown with .850" barrel, Ben Cooley brake: Price of brake $219.99 * Installed., Barrel fluting Add $179.99.
- Competitors Bedding: Sloppy and prone to cracking, will breakdown over time. Still relies on trigger guard to hold action in the stock
- Accuracy Systems, Inc. Bedding: Clean looking! We use three steel pillars (* see above) epoxied into the stock. Then we use three steel screws to bolt the receiver to the stock.
Now you can take your receiver out as many times as you like not effecting the bedding and it always remains strong - $99.95.
- Competitors "claimed heavy barrel". They give you a discount and take a short cut to do it. Notice that where the gas block goes the barrel is very thin. This is a harmonic weak spot prone to barrel vibration! We do not do this.
- Close up of the competitor's thin spot. This other company saves you $85.00 by using your gas block, but it will cost you in accuracy.
- Competitor's target crown. Notice that the crown is not sharp and crisp. The barrel also looks like the end of a baseball bat.
- Our 11° target crown is sharp and crisp. This is a must for accuracy! The muzzle also looks more like a gun barrel.
- Our chamber is 1" thick for 4". The competitors is .900" for 2". Which chamber do you think is more rigid?
- This is the thinnest point of our barrel and it is still .750". No thin spot in this barrel!!
- Very small shoulder to give the gas block support.
Standard Match with .900" diameter, 20" Matte Black Barrel, Front Tactical Sight, Satin Stainless .900" Gas Block with Stud
There are other companies out there that actually call this their heavy barrel. Stay clear you are just asking to be let down. This is one that has been sent to us to replace with our true heavy barrel. This customer's out his $350.00. You will pay more with us but you will be satisfied with what you get back. You pay for what you get.
| 1. |
|
||||
| 2. | |||||
|
BEST MAGAZINES ON THE PLANET! (Others are a waste of money)
WE DO HAVE A VERY LIMITED SUPPLY LEFT.
|
Mini 14 - 20 Round - PRICE $47.99 each SOLD OUT Mini 14 - 30 Round - PRICE $55.99 each SOLD OUT Mini 30 - 20 Round - PRICE $55.99 each SOLD OUT |
NEW 30 ROUND - MINI 14 MAGAZINE
PRICE $39.99 EACH - SOLD OUT |
PRICES SUBJECT TO CHANGE WITH OUT NOTICE!
1.) A. Non-folding Ramline (14oz weight) B. Folding Ramline (14oz weight) 
2.) Hogue - soft over molded, 1" longer than the factory with recoil pad and sling stud 
3.) Butler Creek - with recoil pad and sling stud 
4.) Custom Black/Gray laminate wood stock. These are beautiful. |
New - Aircraft Grade Hard Anodized Aluminum Black Mini 14 Stock
New - Aircraft Grade Hard Anodized Aluminum Black Mini 14 Stock shown with action & 20" heavy fluted barrel.
Features
|
6.) Tactical Synthetic - Rubber recoil pad, sling swivel and cheek rest 
7.) Tactical Synthetic - same as #6, but with no cheek rest 
8.) Custom Brown/Brown laminate   
9.) SCAR - All Machined From Solid 6061 Aluminum Billet (Most advanced stock on the planet).  
9B.) Same as above but California legal 
10.) Tactical Graphite with Recoil Pad 
13.) Butler Creek (non-folding or folding )  Price $39.95 Order # 13-A 
Large Cheek Rest Price $59.95 #13-B Nice quality, Very Comfortable
   18) Tactical Graphite with Adjustable cheek riser. Price $269.99   High Cheek Custom 19.) ASI Custom thumbhole Nutmeg with recoil pad $289.99  21.) MPI Tactical Light weight graphite $349.95 
 22.) The best synthetic stock on the market. Very rigid, Full size recoil pad, Full size rifle feel. Matte textured finish and great feeling cheek swell for proper eye alignment. $99.99  
23) Adjustable Target stock Brown laminate OR Gray & Black Laminate – With adjustable Comb & Butt $239.95
24) Left Hand - Gray & Black Laminate - $239.95
|
Winged three bladed front sight with adjustable height front post$119.95 (installed) Fits .750" diameter or larger barrels.
Comes in High Visible Red or Green
Price installed $79.95
Can be installed on all barrel diameters!MINI 14 & MINI 30 RANCH RIFLES
|
|
|
No More Fumbling With Difficult Adjustments!
 Mini 14 / 30 Ranch Rifle with original sight. |
With New-SIGHT installed.
|
- All Steel Construction
- Easy Click Adjustments on Elevation
- Easy Click Adjustments on Windage
- Standard .062" Aperture
- Available apertures with the Improved Aperture Sight are .042", .086", & .125" - Price $15.99
- Easy installation
- Adds adjustment ease to the 580 / 581 series produced from 2005 to present
You asked for it! You got it!
|
|
|
Milled Rear Sight for Ranch Rifles
PRICE $79.99
|
|
* Testimonial *
Hello,Rear sight M1-A Carbine style for Ruger Ranch duly received yesterday. I have mounted this nice piece and the result is very very good.
Thanks again.Kindly regards from France.
Jean Claude MARTINET
NON - RANCH MODEL MINI 14 RIFLE
- All Steel Construction
- Spring Preloaded Assembly eliminates aperture wiggle present in original sight design
- Easily adjusted for Windage and Elevation - 1/2 MOA Windage, 1 MOA Elevation
- Standard .062 Aperture
- Optional Aperture Sizes Available with IRAS Aperture System
- Easy installation
- Detent Locking
- Better sight picture and Field of View for faster target acquisition
PRICE $79.99
YOU ASKED FOR IT AND WE DELIVERED!! 
COMING SOON. GENERATON 5 - ACCU-STRUT COMPATABLE ADJUSTABLE GAS BLOCKS.
Tired of hitting the fellow 3 shooting benches down in the head and him throwing the brass back at you?
Tired of having to change gas bushings only to find you didn't get the right diameter installed and had to start the process all over again?
Our New Adjustable Gas System
- Will allow you to save all the lost brass that is ejected normally 20 to 30 feet by your factory gas system.
- Will save your scope as well as your receiver during the violent impact that happens every time you fire a round and the operating rod whacks the receiver.
- Will actually help your rifle shoot better by reducing the harmonics that are produced when the operating rod comes in contact with your receiver during high speed cycling of the operating Rod.
- Can be adjusted from no cycling at all for you single shot bench shooters to wide open for you high capacity magazine junkies who don't care where there brass ends up. But some where in between is best.
- Installation is as easy!
- We offer the New Generation 4 with the precise positive click adjusting knob. No adjusting wrench needed.
- The Generation 1 that looks like the factory for those needing to be able to attach accessories to the top of the block.
- All above are available in the .562", .625" and in some conditions in the .750" diameter.
- The NEWEST Adjustable gas block is the GENERATION 4.
- We have added more features that you have asked for.
- A more stream lined look like the Ruger factory.
- Compatibility with after market products that mount to the top of the Ruger factory gas block.
- Like Our ASI Scout Mount, Amega Ranges Scout Mount, Ultimak Scout Mount.
- More Stream lined not as bulky
- Hole pattern matches factory Top & Bottom
- Will fit our Scout mount bolt pattern
- Will fit Amega Ranges & AltiMAK Scout Mounts
- Fits also Ranch Products Scout Mount
- Positive Click no back out adjustment Knob
- Available in Matte Black & Nickel (Closest to Stainless Steel Finish)
- Complete with Adjusting knob, Gas pipe, Top & Bottom of gas block, Sling Swivel stud, & 4 screws. (You use your gas bushing)
- Available in .625" diameter to fit: Mini 14 580/581/582 Series, Target Model, Mini 30 & 6.8.
- Also Available in .562" diameter to fit: Mini 14 181 thru Pre 580 Series.
PRICE $119.99
- Installation is as easy as removing the four factory screws that hold your gas block top and bottom together.
- Then installing our new gas block, new gas pipe. Re-use your gas bushing and top half of block.
- Put your four factory screws back in.
- New Screws are available @ $1.25 each and Top @ $10.00 when purchasing our gas block.
- Milled front for Quick sling connection attachment. (Swivel not included add $14.99 if needed)
- Gas blocks are available in Black or stainless steel.
.625" Diameter Fit's Mini 14 - 580, 581 & 582 Series, Target Model, Mini 30 and 6.8.
. 562" Diameter Fit's Mini 14 - 181 Thru Pre- 580 Series.
PRICE $119.99
Gas Pipe Gen. I, II &III - $29.99
Adjustment / Metering Screw Gen. I & II - $3.99
Adjustment / Metering Screw Spring Gen. I & II - $2.99 EACH
Housing Screw 8-40 Black Gen. I - $1.25 EACH
Housing Screw 8-40 Gray Stainless Gen. I - $1.50 EACH
Housing Screw 8-32 Black Gen. II & III - $1.25 EACH
Housing Screw 8-32 Bright Stainless Gen. II & III - $1.50 EACH
Adjustment / Regulator Knob Kit (Assembled) Gen. III - Black Or Metallic - $29.99
Adjustment / Regulator Knob (Unassembled) Black Or Metallic - $19.99
Adjustment / Regulator Knob Plunger - $2.00
Adjustment / Regulator Knob Plunger Spring - $1.50
Adjustment / Regulator Knob Front Retaining Screw - $2.00
Adjustment / Regulator Knob Metering Screw - $3.99
|
||
| Barrel Diameter | Purchase Price | Manufacturer |
| 1.00" | For barrel conversions only not for sale separately. | Accuracy Systems Gas Block |
| .850" | For barrel conversions only not for sale separately. | Accuracy Systems Gas Block |
| .750" | For barrel conversions only not for sale separately. | Accuracy Systems Gas Block |
Ruger Factory Replacement Gas Block Pricing
|
||
| .625"
Fits Mini 14 - 580, 581 & 582 Series, 6.8, Target, & Mini 30 Only |
Stainless Steel - $94.99 Blued - $89.99 Screws & Top Half Included |
Ruger Factory Replacement Gas Block |
| .562" Fits Mini 14 - 181 Thru Pre - 580 Series |
Stainless Steel - $94.99 Blued - $89.99 Screws & Top Half Included |
Ruger Factory Replacement Gas Block |
Mini 14, Mini 30, 6.8SPC & Target Model
.562" or .625" Blued or Stainless $33.99
Gas Bushing Kits Mini 14/6.8 or Mini 30
Drop brass at your feet, not the next guys head!
Kit 1 Includes - .040", .045", .050"- $14.99
Kit 2 Includes - .035", .040", .045", .050" - $19.99
Individual bushing are $5.29 Each
Red Arrow - Shows the location of the Accuracy Systems .040" gas bushing installed.Blue Arrow - Shows for reference the location of the Ruger factory gas pipe installed.
A. Factory Replacement Length Guide Spring - PRICE $12.99
B. RECOIL REDUCTION GUIDE SPRING - PRICE $17.99(A Must for faster Bolt lock up & less battering of your action)
|
Extra Power Guide Spring Replaces the Factory Guide Spring Shown Below
|
PRICE - $399.99
|
|
Hammer Spring shown compressed with a small allen wrench being used to captivate the spring on the hammer strut. This will allow you to remove the spring & strut together when the pressure is released. Reverse the order to install the new spring.
|
** A Must for those choosing to shoot steel cased Wolf Ammo!
The Extra Power Hammer Spring will help eliminate the misfired rounds caused by hard primers.
This Extra Power Hammer Spring will give the hammer more force which in turn will hit the firing pin harder.
PRICE $13.99
Our most effect / ASI Maxi brake
60% reduction in muzzle rise and recoil. 3" Long x .900" at the back and 1.250" at the front.
Small 3 Port $89.95 (installed add $100.00) * Large 3 Port $99.99 (Installed add $129.99)
Stainless 360 degree 32 port Maxi brake
very effective for those wanting a flush fit. Available in Black.
$89.99(installed add $100.00)
Ben Cooley Brake
2.75" Long x 1" Diameter
$99.00(installed add $100.00)
Adjustable Boss™ Harmonic tuner & Brake
Available in black or silver shown. 3" Long x 1" diameter.
$289.95 (installed)
ASI Quiet Linear Compensator
(Size 1.125" Diameter x 2.25" Long) Add $35.00 to turn OD down to your size. Available in Black.
$79.99 (installed add $100.00)
You asked for the tool and we now have it.
$32.99
Varmint Brake
no bottom holes all holes slant forward 11˚
$99.95 (installed add $100.00)
New - Tapered Quiet Brake
| $99.99
Price - Brake Only |
|
* Ask about discounts on brakes when we do your barrel conversion
New Extender Rail 6.875" long (for Non Ranch Model). 
You asked for it and we delivered! This Mount can be installed by drilling & tapping the front of the receiver Or it can be used with out drilling & Tapping the receiver. However, drilled and tapped installation is recommended for the most stable scope mount available. You remove your existing rear sight and utilize the existing holes in the receiver to mount the scope base. Or you can have us or your local gunsmith tap the receiver for one threaded hole in the front of the receiver. A hole is already provided in the front of the mount for this option. 5.375" PRICE $109.99 (Installed Add $40.00)
6.875" PRICE $119.99 (Installed Add $40.00) |
| A |
 |
|
|
|
ASI Mini 14 or 30 Ranch Rifle 4 7/8" Scope Rail.
$79.99 Black Only |
|
|
|
|
| B |
|
| Urban Brawler Full Rail For Mini 14 or 30 & 6.8 All rifles | |
|
|
 Ranch Rifle shown with Urban Brawler full rail |
|
| D |
New Compact - See thru Scout Mount
|
|
| F |
|
Extends 10.5" from just in front of the rear sight to just 2" behind the gas block. Very Ridged!
Price $99.95
|
Newest Improved Extended Magazine Release
|
|
OURS Ruger® FACTORY |
|
